Product Name :
YMGI SINGLE ZONE CONCEALED DUCT 12,000 BTU SEER 22 1 TON Cool and Heat Pump
|
|
|
|
Item# :
|
ymgi-cassette-30CH-12EF
|
|
|
|
Choose QTY
:
|
Required
|
|
|
|
|
|
DescriptionAir is drawn through the center grilles/filters and then discharged at 4 vents in 4/8 directions. Less than 24? and so will fit into the 24? ceiling joints. Description Model Number | Unit / Conditions | WMMS-12EC-V2B(59)2 | Power Supply | Voltage/Ph/Hz | 208-230/1/60 | Allowed Voltage Range | 187-253V | Cooling Capacity (Btu/h) | High/Standard/Low | 13900/12000/5200 | Heating Capacity (Btu/h) | ID 70/60, OD 47/43F | 13000 | ID 70/60, OD 17/15F | 11600 | ID 70/60, OD 17/5F | 9000 | SEER | Btu/h.W | 16 | HSPF | Btu/h.W | 8.2 | Duhumidifying Capacity | Pints/Hr. | 2.96 | Air Flow (CFM) | High/Medium/Low | 353/312/245 | Air-throw (Ft.) | Horizontal Installation | 25-18 Upon Mounting Height/Speed/Temp. | External Static Pressure | Water In. | 0 | Sound Level | Pressure dB(A) (H/M/L)) | 39/37/35 | Power dB(A) (H/M/L) | 49/47/45 | Fan Motor | Model | FN11T-2 | Shaft | Single | Speed (RMP, H/M/L) | 700/600/5151 | Output (W) | 11 | Input (W) | 50 | Capacitor (uF) | 1 | Fan Wheel | Type-Piece | Centrifugal-1 | Diameter x Height (In.) | 11.1 x 5.8 | Swing/Step Motor | Model | MP35CB | Piece | 2 | Output (W) | 2 | Input Power of Ele. Heater | NA | Electrical Protection Fuse | T3.15A 250V / 0.2A | Evaporator Coil | Type | Alu. Fin/Inner Grooved Copper Tube | Color | Blue | Copper Line Connections | Sealed by Dry Nitrogen | Yes | Flare/Nut-Liuqid + Gas | 1/4? + 3/8? | Drain Hose Connection | OD (In.) | 1.22 | Condensate Pump | Installed-Lift (In.) | Yes-25 | Refrigerant Environmental Friendly | R410A | Yes | Filter | Type-Feature | Standard-Washable | Size WxH (In.) – Qty. | 13.56 x 13.13 – 1 | Clean Coil Surface | Anti-Mildew Function | Yes | Pre-heating Function | Anti-Cold Blowing | Yes | Memory of Previous Set-ups | Power is Lost/Resumed | Yes | Auto-Restart Function | If Power is Resumed | Yes | Unit Dimensions | Net L x W x H (In.) | 22.4 x 22.4 x 9.1 | Package L x W x H (In.) | 33.4 x 28.7 x 12.2 | Unit Weight | Net (LBs) | 39.7 | Packaged (LBs) | 50.7 | Face Panel Dimensions | Net L x W x H (In.) | 25.6 x 25.6 x 2 | Package L x W x H (In.) | 28.7 x 26.4 x 4 | Face Panel WeightNet (LBs) | 5.5 | Packaged (LBs) | 8.1 | Loading Capacity | 20’/40’/40’HQ | 102/209/246 |
YMGI Specifications: DC Inverter Mini Split Heat Pump-Multiple Zone-(59)4 Outdoor Units 22 SEER |
Model |
Units |
WMMS-30CH-V2B(59)4 |
Cooling Capacity Rating-Standard Comp. Speed |
Btu/h |
18000 |
Min./Max. Cooling Capacity |
Btu/h |
6998 / 21000 |
Heating Capacity Rating-Standard Comp. Speed |
Btu/h |
19000 |
Min./Max. Heating Capacity |
Btu/h |
7000 / 22600 |
Max. Allowed IDU Qty./Capacity Total |
# / Btu/h |
2 / 30,000 |
EER W/W, (Btu/h)/W |
W/W |
3.66 / 12.50 |
COP W/W, (Btu/h)/W |
W/W |
3.66 / 12.50 |
SEER / HSPF |
- |
22.00 / 10.50 |
Air Flow Volume |
CFM |
1883 |
Sound Pressure / Power Level |
dB(A) |
56 / 63 |
Power Supply |
V/Ph/Hz |
208-230/1/60 |
Power Cable Conductor Minimum Size |
AWG |
AWG 14, Following NEC |
Recommended HVAC Type Circuit Breaker Size |
Amp. |
20 |
Power Input Cooling / Heating / Rated |
KW |
1.44 / 1.52 / 2.80 |
Current Input Cooling / Heating / Rated |
A |
6.26 / 6.61 / 12.42 |
Compressor Type, Model |
- |
Inverter Rotary, LD QXA- B141zF030A |
Compressor Capacity / Input |
W |
4320 / 1440 |
Compressor RLA / LRA |
A |
10.82 / - |
Compressor Thermal Protector KINGERSONS |
- |
Exterior 1NT11L—6233 |
Compressor Crankcase Heater |
W |
25 |
Compressor Oil Type, Charge |
-, OZs |
RB68EP, 13.7 |
De-Ice/Snow Heater Power Input |
W |
96 |
De-Ice/Snow Heater Current |
A |
0.4 |
Fan Type / Qty. / Diameter-Height |
- |
Axial-flow / 1 /D550-H65mm |
Motor Model / Type |
- |
LW60M-ZL, DC |
Motor Insulation Class, Safe Class |
- |
E, IPX4 |
Fan Motor Drive Type, Speed |
- |
Director Drive, 630 |
Fan Motor Power Output / Input |
W |
60 / - |
Motor Full Load Amp (FLA) |
A |
- |
Condenser Materials |
- |
Aluminum Fin-Copper Tube |
Permissible Operating Pressure for the Discharge/Suction Sides |
PSI |
600 / 360 |
High/Low Pressure Overload Protector |
PSI |
580 / - |
Cooling Operation Ambient Temperature Range |
F |
0 ~ 118 |
Heating Operation Ambient Temperature Range |
F |
-4 ~ 75 |
Defrosting Method of Heat Pump in
Low Temperature Ambient |
-- |
Automatic Reversing, Fan
Cycling |
Pressure Maitenance Method in Low
Temperature Cooling |
-- |
Automatic Fan Speed
Control, Cycling |
Overload Protector |
- |
Current+Temperature |
Designed for Climate Type, Moisture Protection |
- |
T1, IPX4 |
Refrigerant, Charge |
LBs |
R410A, 3.5 |
Metering Device KINGERSONS |
- |
Electronic expansion valve |
Flare/Nut Valve Size-Liquid |
Inch |
1/4, 1/4 |
Flare/Nut Valve Size-Gas |
Inch |
3/8, 3/8 |
Min. Allowed Copper Line Length/Unit |
Ft. |
15 |
Max. Allowed Copper Line Length-
outdoor to last indoor unit |
Ft. |
65 |
Max. Elevation Difference Allowed-
outdoor unit is below all indoor units |
Ft. |
35, Oil Trap is Not Needed |
Max. Elevation Difference Allowed-
outdoor unit is above indoor units |
Ft. |
35, Oil Trap is Suggested
Every 18' |
Max. Copper Line Length (all together) |
Ft. |
130 |
No Additional Refrigerant Needs to be Added, If Copper Line Length Total is Less Than |
Ft. |
60 |
Refrigerant Charge Rate, If Needed, by
Weight/Ft. of Extra Liquid Line Length |
Ozs/Ft. |
2.32 |
Dimension of Unit Outline (W×D×H) |
Inch |
37.6x15.6x27.6 |
Dimension of Package (W×D×H) |
Inch |
40.5x18.0x29.5 |
Weight-Net / Gross |
LBs |
115 / 124 |
Loading Quantity (20’/40GP/40HQ) |
Units |
81 / 171 / 171 |
|
YMGI Group, specializes in researching and utilizing state-of-the-art technologies and new materials, innovatively designs, manufactures, markets energy-efficient and environment friendly air conditioner and heat pump units of all types, including, but not limited to:
Split Ductless Systems: (DC inverter and fixed speed) split wall mounted, ceiling mounted cassette, floor mounted free standing, ceiling/floor mounted universal...WMMS Packaged Ductless Systems: mini wall mount packaged unit, portable AC/HP, PTAC/PTHP, air source heat pump (water chiller and heater, roof top.... Split Indoor Units: Horizontal flow and upflow fan coil units...SFCU Special Condensing Units: side-discharge compact foot-print SHCR, through-the-wall TTWC
We provide nitche and smart HVAC solution for residential, light commercial, institutional, hospitality, industrial and other applications.
YMGI Group operates several facilities to R&D, manufacture, distribute HVAC equipment and parts and accessories, support and service customers. YMGI Group R & D team consists of highly experienced professionals. Our labs provide non-stop support to R & D and quality control. YMGI Group tightly controls all processes from design, components, equipment assembly, inspection to shipping.
YMGI Group provides technical support and customer service in all means. YMGI Group is a strong management-engineering-marketing entity, connecting to thousands of HVAC & R customers. YMGI Group grows and expands steadily.
YMGI Group brought and will continue to bring comfort and satisfaction to all customers around the world.
YMGI Group Mission: -To provide high quality of products and service to improve life quality of all customers, to the ultimate satisfied level possible. -To research and develop technologies and products to help build and maintain sustainable green and energy efficient world.
|
|
YMGI Group R & D strives to bring up energy-efficienct and enviorment friendly products, in an endless effort to build up a sustanable world.
Thanks to the cutting edge technology, and the generous offer from mankind's mother-earth, and dad-sun, and other relatives in the universe possible, YMGI Group R & D products that help people untilize energy from:
* Air source * Water source * Ground source * Solar source
YMGI Group R & D consists of highly skilled professionals of experience. YMGI Group can customize R & D products towards various marketing needs, no matter what quantity, what time-frame, what format the customers are looking for.
Manufacturing, is not just a whole bunch of work, as scheduled, to put all the components together, but only one, among many stations, to make a medium (product), which can not only physically be capable of bringing energy efficient and thermally satisfied and psycologically clean comfort, to people and other usage in special applications, once properly delivered and correctly installed.
Also, YMGI views the manufacturing a key process, to allow the medium(product) spiritually inspire people passion to enjoy a happy life, and pass on the value of building up a environmental friendly and sustainable world, for the generations next and next, on and on...
YMGI Group R & D the needed, manufactures the "R & D" and needed, to the quality at our best. YMGI man-u-fact-ure, yes, YMGI Group makes for you, as a matter a fact, all you expected and will expect in the future.
With the state-of-the-art equipment, trained personnel, strigently contolled QC and QA, anything of quality, is to be manufactured.
YMGI Group designs and selects components of quality. These components must work perfectly, both individually and jointly, at initial testing and life-time cycle running...
Compressors-Scroll, Rotary; 1Ph, 3Ph; Copeland, Danfoss, Toshiba, Matsushita, Sanyo, Hitachi...
Motor-AC, DC; PSC, ECM...
Expansion Valve: External balancing, internal balancing; Danfoss, Sanhua...
Control-On/off, ADP; On-demand, temperature, pressure, time; Linear, Non-linear...
Fan wheel/blade: cross-flow random pitch, low noise, high efficiency
Packing materials: regular, recycle...
|
Warranty From The Manufacturer - Only applies to units installed by licesensed HVAC Or Air Conditioning company.
- 1 years parts
- 5 years compressor
COMPLETE DETAILS:
If you received a product that is "Dead On Arrival" we will replace it with brand new unit. You have 15 days from the date of delivery to notify us of the same.
Please make sure that you have an invoice from the licensed HVAC (or air conditioning company) with our model number AND serial number to receive any warranty. Replacement parts will be shipped and credit will be given when the part is returned to supplier. You will not receive credit for replacement units or warranty parts without proper documentation. Proper documents include an invoice from us and an invoice from a licensed installer. Our invoice will be emailed to you with the tracking number that you can print and save for future reference.
NO LABOR. THESE LIMITED WARRANTIES DO NOT INCLUDE LABOR or any other costs incurred for service, maintenance, repair, removing, replacing, installing, complying with local building and electric codes, shipping or handling, or replacement of the System, compressors or any other parts. For items that are designed to be maintained or replaced by the owner, the owner is solely responsible for all labor and other costs of maintaining, installing, replacing, disconnecting or dismantling the System and parts (such as filters or belts) in connection with owner-required maintenance. Air filter cleaning and/or replacement for each applicable indoor unit are owner-required maintenance, and labor for this procedure is not covered under warranty. Please consult the applicable technical documentation for air filter cleaning and other maintenance procedures.
D. Proper Installation. This Limited Warranty applies only to Systems that are installed by contractors who are licensed for HVAC installation under applicable local and state law, and who install the Systems in accordance with (i) all applicable building codes and permits; (ii) YMGI’s installation and operation instructions; and (iii) good trade practices.
BEFORE REQUESTING SERVICE, please review the applicable technical documentation to insure proper installation and correct customer control adjustment for the System. If the problem persists, please arrange for warranty service.
1. TO OBTAIN WARRANTY PARTS SERVICE:
(a) Contact the licensed contractor who installed the System or the nearest licensed contractor, dealer or distributor of any defect within the applicable warranty time period.
(b) Proof of the installation date by a licensed contractor is required when requesting warranty service. Present the sales receipt, building permit or other document which establishes proof and date of installation. Otherwise, this Limited Warranty shall be deemed to begin one hundred twenty (120) days after the date of manufacture stamped on the System. THE RETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please return the Owner Registration Card so that YMGI can contact you if a question of safety arises.
(c) This Limited Warranty applies only while the System remains at the site of the original installation and only to locations within the continental United States, Alaska and Hawaii.
2. THIS LIMITED WARRANTY DOES NOT COVER: property damages, malfunction or failure of the System, or personal injury caused by or resulting from: (a) accident, abuse, negligence or misuse; (b) operating the System in a corrosive or wet environment containing chlorine, fluorine or any other hazardous chemicals; (c) installation, alteration, repair or service by anyone other than a licensed contractor or other than pursuant to the manufacturer’s instructions; (d) improper matching of System components; (e) improper sizing of the System; (f) improper or deferred maintenance contrary to the manufacturer’s instructions; (g) physical abuse to or misuse of the System (including failure to perform any maintenance as described in the Operation Manual such as air filter cleaning, or any System damaged by excessive physical or electrical stress); (h) Systems that have had a serial number or any part thereof altered, defaced or removed; (i) System used in any manner contrary to the
Operation Manual; (j) freight damage; or (k) damage caused by force majeure or other factors such as power surge damage caused by lightning and fluctuations in or interruptions of electrical power.
3. THIS LIMITED WARRANTY ALSO EXCLUDES: (a) SERVICE CALLS WHERE NO DEFECT IN THE SYSTEM COVERED UNDER THIS WARRANTY IS FOUND; (b) System installation or set-ups; (c) adjustments of user controls; or (d) Systems purchased or installed outside the continental United States, Alaska and Hawaii. Consult the operating instructions for information regarding user controls.
4. This Limited Warranty shall not be enlarged, extended or affected by, and no obligation or liability shall arise or grow out of, YMGI providing, directly or indirectly, any technical advice, information and/or service to Owner in connection with the System.
5. EXCEPT AS OTHERWISE PROVIDED IN THIS LIMITED WARRANTY, YMGI MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SYSTEM. YMGI DISCLAIMS AND EXCLUDES ALL WARRANTIES NOT EXPRESSLY PROVIDED HEREIN AND ALL REMEDIES WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE. NO ONE IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY RESPECT OR TO CREATE ANY OTHER OBLIGATION OR LIABILITY FOR YMGI IN CONNECTION WITH THE SYSTEM. YMGI DISCLAIMS ALL LIABILITY FOR THE ACTS, OMISSIONS AND CONDUCT OF ALL THIRD PARTIES (including, without limitation, the installing contractor) IN CONNECTION WITH OR RELATED TO THE SYSTEM.
6. UNDER NO CIRCUMSTANCES SHALL YMGI BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING, WITHOUT LIMITATION, LOST GOODWILL, LOST REVENUES OR PROFITS, WORK STOPPAGE, SYSTEM FAILURE, IMPAIRMENT OF OTHER GOODS, COSTS OF REMOVAL AND REINSTALLATION OF THE SYSTEM, LOSS OF USE, INJURY TO PERSONS OR PROPERTY ARISING OUT OR RELATED TO THE SYSTEM WHETHER BASED ON BREACH OF WARRANTY, BREACH OF CONTRACT, TORT OR OTHERWISE, EVEN IF YMGI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. IN NO EVENT SHALL YMGI’S LIABILITY EXCEED THE ACTUAL PURCHASE PRICE OF THE SYSTEM WITH RESPECT TO WHICH ANY CLAIM IS MADE.
7. Some states do not allow limitations on warranties or exclusions or limitation of damages, so the above limitations or exclusions may not apply.
8. This Limited Warranty gives the owner specific legal rights and the owner may also have other rights that vary from state to state.
9. This Limited Warranty is valid only in the continental United States, Alaska and Hawaii, and it is not transferable.
SHIPPING DETAILS
Mostly All Of Our Products Are Shipped Same Or Next Day
Your product will be mostly shipped using Freight Company such as SAIA, ESTES, Old Dominion, FEDEX or UPS and will be delivered in 1-5 business days depending upon your geographical location from our warehouses. We ship products from warehouses in NY, NJ, FL, CA,AZ, TX And MO. Mostly if you are close to our warehouses, you should receive the Product in 1-3 business days. We will email you your tracking number soon as its shipped out or you can log into your account on our website by using your email address and password you created at the time of placing order to check all the shipment and product details. Please remember we only ship to 48 states within United States. Due to expensive shipment fee we do not ship to Hawaii & Alaska. We do not ship to Canada, Puerto Rico, Jamaica and other countries due to custom issues.
Though above shipment and delivery process is what we normally practice, under unforseen circumstances they cannot be guaranteed at all times. But we do our best and mostly succeed to ship the product either same or the next day.
Overnight Shipping Details (if required)
We can ship overnight or by Second Day Air. But beacuse these are air conditioners and the package weighs more than 90 pounds usually, shipping overnight can result in the package being mishandled and delivered damaged. Plus it cost anywhere from $180-$850 more than regular shipping depending upon your location from our warehouse. Feel free to email us with such enquiries.
Delivery Acceptance, Returns, Exchanges and Cancellation Policy. |
We truly appreciate your business and for the past 2 decades being in this business we have continued to do our best to earn customer trust with each transaction. We want you to be happy with your purchase.
100% Satisfaction is guaranteed with all your purchases. In case any of the RARE complications occur, we will handle them upto your best interest and satisfaction. |
Delivery Acceptance Terms: If you receive a package that seems damaged or dented, please open the package in front of the driver and after inspection if you see the product has a severe damage you can refuse the package and call us immediately. We will then arrange a new shipment (Free Replacement) ASAP.
Please note: If the box looks visibly damaged, the product inside may still be in perfect condition as they are well padded for shipping purposes.
PLEASE DO NOT SIGN OR REFUSE THE PACKAGE WITHOUT INSPECTING THE CONDITION OF THE PRODUCT INSIDE. Please take pictures if needed, accept or refuse shipment based upon the condition of the product in the box, not based upon the condition of the box. Please remember if you signed off on a delivery document, insurance cannot be filed if cosmetic damage is found at a later date, as it is considered to have happened after delivery at jobsite.
If you need to get in touch with KINGERSONS, please call KINGERSONS customer service number at 1-386-951-1722 OR email us with your query. AS PER OUR WEBSITE, BELOW IS OUR EXCHANGE/RETURN POLICY FOR YOUR REFERENCE.
DEFECTIVE EXCHANGE If unit (any product) is defective, depending upon the brand you buy, it will be taken care of by manufacturer warranty. Usually they will send out the replacement part within 24 hours, if replacing part is not a solution, they would probably replace the whole unit if the product was found defective. Replacement will only be made with the same model, if customer decides to upgrade or downgrade to a different model, we'll treat it as a return and a new order.
* All returns should be in original packaging and in brand new condition. Installed products are not considered brand new and cannot be returned.
* All damaged returns and replacements must be requested within 24 hours after the receipt of the product. *
Before shipping the product back, you should request an RA# (Return Authorization number), without an RA# your package will not be accepted, will be refused and sent back by the warehouse.
RETURNS For all returns, customer is responsible to ship product back to our warehouse at their own expense; restocking fee of 19% will apply regardless if defective and original shipping fee (from $69 to $189 depending upon the product you purchased) will not be refunded as it is paid to the trucking company's and they are non-refundable.
CANCELLATIONS If you placed the order and you wanted to cancel the order BEFORE IT IS SHIPPED, we will gladly cancel your order and $15.99 cancellation fee will be charged and 3% credit card processing charges will not be refunded. Please make sure that you call us within few hours after the order is placed. We ship the items out same or next business day. We cannot process cancellations after the product is shipped out. It will be considered as a return instead once the product is shipped and you will need to pay the return charges. If the delivery of the shipment is refused above return policy will apply. Once the item is shipped, the shipping company will not refund us the shipping fee back and will charge us for shipping both ways, this will not be refunded if cancelled after the product is shipped and 19% restocking fee will apply.
|
THANK YOU ONCE AGAIN FOR SHOPPING WITH US! | |
|
|
|
|
|
|
|
|
|